Shaker Wall Panel Layout for a 13 ft Wall, 8.5 ft Ceiling

Plan shaker wall panels on a 13 ft / 396.2 cm wide wall beneath a 8.5 ft / 259.1 cm ceiling. This example combines a scaled drawing, component quantities and three spacing options so you can compare the layout with your own room before choosing a kit.

Proposed layout: 6 vertical battens create 5 equal bays with 27.6 in / 701 mm clear spacing between 3-inch faces. There are 2 rows of openings, each 44.25 in / 1124 mm clear height.
Shaker Wall Panel Layout for a 13 ft Wall, 8.5 ft Ceiling Proposed wall layout. Horizontal and vertical measurements show the whole wall; the table below gives each piece length.13 ft / 396.2 cm wall width8.5 ft / 259.1 cm ceiling height
A front elevation of this example, including the assumed baseboard. The drawing is a planning layout; it does not show the individual pieces of a particular stocked kit.

Why this arrangement fits the dimensions

A full-height rectangular grid uses uninterrupted vertical battens and short horizontal rails between them. The horizontal pieces are measured between battens, so their lengths differ from the full-width top and bottom rails. At this wall width, start with the drawn division count and compare it with one fewer and one more. Furniture position can matter more than symmetry about the room corners. This ceiling leaves a tighter vertical field. Check that the top outline clears crown molding and that every lower opening clears the baseboard.

Measurements used in the drawing

  • Finished wall width: 156 in / 3962.4 mm
  • Finished floor-to-ceiling height: 102 in / 2590.8 mm
  • 3 in / 76.2 mm assumed batten face width; recalculate for a 75 mm product
  • 2.5 in / 63.5 mm assumed top and bottom rail height
  • 5.5 in / 139.7 mm existing baseboard below the bottom rail
  • Outer battens finish flush with wall edges; equal gaps are between battens

Profile face widths are planning assumptions. A different width changes clear openings and, for nested frames, inner dimensions. Inch and metric displays are rounded; calculate from the full wall run rather than repeatedly adding rounded values.

Component and cut-length schedule

Lengths for the proposed shaker wall panels arrangement
Component Quantity Length each or total run Joint basis
Vertical battens 6 91.5 in / 2324.1 mm Square ends between the top and bottom rails
Top or cap rail total run 1 156 in / 3962.4 mm Splice to suit stock lengths; not one supplied piece
Bottom rail total run 1 156 in / 3962.4 mm Splice to suit stock lengths; not one supplied piece
Intermediate horizontal rails 5 27.6 in / 701 mm Square ends fitted between vertical battens

The schedule totals 83.25 linear ft / 25.37 m, excluding the existing baseboard. A 10% cutting allowance brings the planning quantity to 92 linear ft / 28.04 m, rounded up to the next whole foot. Allowance depends on the supplied lengths, joints and installation method; confirm the final kit quantity before ordering.

Compare division counts

Columns or bays Clear bay width Effect
4 35.25 in / 895.3 mm Wider divisions
5 27.6 in / 701 mm Drawn option
6 22.5 in / 571.5 mm Narrower divisions

The alternatives change the horizontal rhythm; the component schedule above belongs only to the drawn option. If you choose a different count, update the component quantities and lengths together.

Check the wall before ordering

  1. Measure the width at the top, middle and bottom. Record the usable area and any unequal corners.
  2. Mark doors, windows, outlets, switches, vents and fixed furniture on a wall sketch. Keep access and required clearances available.
  3. Tape the frame or batten outlines on the wall and inspect them from the doorway. Adjust around the object that anchors the room.
  4. Compare the selected kit's material, profile face width, supplied sizes and installation instructions with this schedule. Send your measurements for a final layout if they differ.

Explore kits for this look

These products are starting points for the style shown. Their listed configurations may differ from this drawing; compare the product dimensions or request a layout for your exact wall.

Plan my wallBrowse shaker wall panels kits

Questions about this layout

Can I use this for a different wall width?

A different width changes the outside frame width or clear batten spacing. Enter your actual dimensions in the wall designer rather than stretching the drawing by eye.

Are the product kits automatically supplied in these sizes?

No. This is a proposed arrangement. Product pages describe the supplied options; a custom size or a different frame count needs confirmation before you order.

Which measurements should I send from the USA or Canada?

Send wall width, floor-to-ceiling height, baseboard height and obstacle positions. Either inches or metric measurements work; use one unit consistently and state the unit with each dimension.

Continue planning