Double Picture Frame Molding Layout for a 15 ft Wall, 9 ft Ceiling

Plan double picture frame molding on a 15 ft / 457.2 cm wide wall beneath a 9 ft / 274.3 cm ceiling. This example combines a scaled drawing, component quantities and three spacing options so you can compare the layout with your own room before choosing a kit.

Proposed layout: 5 columns and 20 frames in total, with 31.2 in / 792.5 mm outside frame width and 4 in / 101.6 mm clear gaps. The top of the chair rail is 40.5 in / 1028.7 mm above the finished floor.
Double Picture Frame Molding Layout for a 15 ft Wall, 9 ft Ceiling Proposed wall layout. Horizontal and vertical measurements show the whole wall; the table below gives each piece length.15 ft / 457.2 cm wall width9 ft / 274.3 cm ceiling height
A front elevation of this example, including the assumed baseboard. The drawing is a planning layout; it does not show the individual pieces of a particular stocked kit.

Why this arrangement fits the dimensions

Each outer frame contains a smaller inner frame. The inner outline is inset by the assumed profile face width plus a 1.5-inch clear gap. Both frame sets are included in the material allowance. At this wall width, start with the drawn division count and compare it with one fewer and one more. Furniture position can matter more than symmetry about the room corners. This ceiling gives more room for vertical proportions. Keep outlets and furniture in the sketch rather than stretching a standard kit without checking its listed dimensions.

Measurements used in the drawing

  • Finished wall width: 180 in / 4572 mm
  • Finished floor-to-ceiling height: 108 in / 2743.2 mm
  • 1.25 in / 31.75 mm assumed frame profile face width
  • 4 in / 101.6 mm outer side margins and clear gaps
  • 5.5 in / 139.7 mm existing baseboard; 4 in clearance above it
  • 5 in / 127 mm upper clearance on tall and two-row frames
  • 2.5 in / 63.5 mm assumed chair rail height
  • 1.5 in / 38.1 mm clear gap inside each outer frame

Profile face widths are planning assumptions. A different width changes clear openings and, for nested frames, inner dimensions. Inch and metric displays are rounded; calculate from the full wall run rather than repeatedly adding rounded values.

Component and cut-length schedule

Lengths for the proposed double picture frame molding arrangement
Component Quantity Length each or total run Joint basis
Upper frame horizontals 10 31.2 in / 792.5 mm 45° miters; long-point length
Upper frame verticals 10 58.5 in / 1485.9 mm 45° miters; long-point length
Upper inner frame horizontals 10 25.7 in / 652.8 mm 45° miters; long-point length
Upper inner frame verticals 10 53 in / 1346.2 mm 45° miters; long-point length
Lower frame horizontals 10 31.2 in / 792.5 mm 45° miters; long-point length
Lower frame verticals 10 24.5 in / 622.3 mm 45° miters; long-point length
Lower inner frame horizontals 10 25.7 in / 652.8 mm 45° miters; long-point length
Lower inner frame verticals 10 19 in / 482.6 mm 45° miters; long-point length
Chair rail total run 1 180 in / 4572 mm Splice to suit available lengths; plan corners separately

The schedule totals 239 linear ft / 72.85 m, excluding the existing baseboard. A 10% cutting allowance brings the planning quantity to 263 linear ft / 80.16 m, rounded up to the next whole foot. Allowance depends on the supplied lengths, joints and installation method; confirm the final kit quantity before ordering.

Compare division counts

Columns or bays Outside frame width Effect
4 40 in / 1016 mm Wider divisions
5 31.2 in / 792.5 mm Drawn option
6 25.333 in / 643.5 mm Narrower divisions

The alternatives change the horizontal rhythm; the component schedule above belongs only to the drawn option. If you choose a different count, update the component quantities and lengths together.

Check the wall before ordering

  1. Measure the width at the top, middle and bottom. Record the usable area and any unequal corners.
  2. Mark doors, windows, outlets, switches, vents and fixed furniture on a wall sketch. Keep access and required clearances available.
  3. Tape the frame or batten outlines on the wall and inspect them from the doorway. Adjust around the object that anchors the room.
  4. Compare the selected kit's material, profile face width, supplied sizes and installation instructions with this schedule. Send your measurements for a final layout if they differ.

Explore kits for this look

These products are starting points for the style shown. Their listed configurations may differ from this drawing; compare the product dimensions or request a layout for your exact wall.

Plan my wallBrowse double picture frame molding kits

Questions about this layout

Can I use this for a different wall width?

A different width changes the outside frame width or clear batten spacing. Enter your actual dimensions in the wall designer rather than stretching the drawing by eye.

Are the product kits automatically supplied in these sizes?

No. This is a proposed arrangement. Product pages describe the supplied options; a custom size or a different frame count needs confirmation before you order.

Which measurements should I send from the USA or Canada?

Send wall width, floor-to-ceiling height, baseboard height and obstacle positions. Either inches or metric measurements work; use one unit consistently and state the unit with each dimension.

Continue planning