Picture Frame Molding Without Chair Rail: 18 ft Wall Sizes
This 18 ft wall and 8 ft ceiling example compares complete full-height picture frames arrangements, not only panel widths. Use the setting-out coordinates to mark the wall, then compare the material and clear-opening changes before selecting a kit.
How the width and openings were calculated
(216 − 8 − (6 − 1) × 4) ÷ 6 = 31.333 inches outside frame width. Subtract two 1.25-inch profile faces for the visible opening: 28.833 in / 732.367 mm.
Four-inch side margins and gaps; 1.25 in / 31.75 mm profile faces; 5.5-inch existing baseboard. The chair rail, when present, has an assumed 2.5-inch face.
Compare complete alternatives for this wall
| Columns / bays | Clear opening width | Clear opening height | Listed pieces / runs | Net material | With 10% allowance | Difference |
|---|---|---|---|---|---|---|
| 5 | 35.9 in / 911.86 mm | 79 in / 2006.6 mm | 20 | 99.917 linear ft / 30.455 m | 110 linear ft / 33.528 m | 12.917 linear ft less trim |
| 6 | 28.833 in / 732.367 mm | 79 in / 2006.6 mm | 24 | 112.833 linear ft / 34.392 m | 125 linear ft / 38.1 m | Illustrated |
| 7 | 23.786 in / 604.157 mm | 79 in / 2006.6 mm | 28 | 125.75 linear ft / 38.329 m | 139 linear ft / 42.367 m | 12.917 linear ft more trim |
Across these options the net material ranges from 99.917 linear ft / 30.455 m to 125.75 linear ft / 38.329 m. Fewer divisions widen the openings; more divisions add vertical edges. Choose using furniture and artwork outlines rather than assuming the highest panel count is better. The cut schedule below belongs to the illustrated 6-division option.
Cut schedule and material allowance
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 81.5 in / 2070.1 mm | Outside long point; 45-degree miters |
The listed components total 112.833 linear ft / 34.392 m. A 10% cutting allowance, rounded up to a whole foot, gives 125 linear ft / 38.1 m. This includes only the listed components; baseboards, adhesive, paint and unlisted return pieces are separate. Continuous rails are total runs, not a promise of one supplied piece.
Setting-out positions from one fixed corner
Measure horizontally from the finished left corner and vertically up from the finished floor. The table uses outside frame edges or board edges, not the center of a pencil line. Mark positions directly from the origin so rounded gaps do not accumulate.
| Element | Left edge from corner | Right edge from corner | Top above floor | Bottom above floor |
|---|---|---|---|---|
| Tall frame 1 | 4 in / 101.6 mm | 35.333 in / 897.467 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
| Tall frame 2 | 39.333 in / 999.067 mm | 70.667 in / 1794.933 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
| Tall frame 3 | 74.667 in / 1896.533 mm | 106 in / 2692.4 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
| Tall frame 4 | 110 in / 2794 mm | 141.333 in / 3589.867 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
| Tall frame 5 | 145.333 in / 3691.467 mm | 176.667 in / 4487.333 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
| Tall frame 6 | 180.667 in / 4588.933 mm | 212 in / 5384.8 mm | 91 in / 2311.4 mm | 9.5 in / 241.3 mm |
What changes when your measurement changes?
| Measured change | Clear width | Clear height | Recalculated net trim | Change from illustrated |
|---|---|---|---|---|
| Wall 215 in; same count | 28.667 in / 728.133 mm | 79 in / 2006.6 mm | 112.667 linear ft / 34.341 m | -0.167 linear ft |
| Wall 217 in; same count | 29 in / 736.6 mm | 79 in / 2006.6 mm | 113 linear ft / 34.442 m | 0.167 linear ft |
| Ceiling 102 in; same count | 28.833 in / 732.367 mm | 85 in / 2159 mm | 118.833 linear ft / 36.22 m | 6 linear ft |
At a fixed count of 6, a one-inch wall-width error changes each frame or bay by 0.167 in / 4.233 mm. A different count, profile face or rail position requires a full recalculation. The taller-ceiling row follows this example’s proportional rail/cap rule; an existing fixed rail needs a separate calculation.
Worked example: artwork inside a tall frame
The illustrated tall opening is 28.833 in / 732.367 mm wide by 79 in / 2006.6 mm high after subtracting the assumed profile faces. If you reserve a 2-inch visual margin inside each side, the artwork’s maximum outside width in this test becomes 24.833 in / 630.767 mm. Include the artwork frame and any picture-light backplate; an advertised print size does not describe those outside dimensions. The 2-inch margin is a design test, not a mounting requirement.
FREE WALL CALCULATOR
Plan your wall in 60 seconds
Enter your wall size. Get frame sizes, spacing, total molding length and your kit price. Save $20 on orders over $350 with code WALL20.
Calculate my wall Get a free design drawingShop Picture Frame Molding Kits
View all
Picture Frame Ready to Assemble Wall Molding Kit, 3 Upper & 3...From $217.20Choose options
Nested Frame Nursery Wall Molding Kit, Ready to AssembleFrom $300.00Choose options
Nested Picture Frame French Trim Wall Molding Kit, 2 Frames, ...From $132.00Choose options
Panel Molding by the Meter, 2.5 cm and 4 cm PolystyreneFrom $129.60Choose options
Peel and Stick Wall Molding Kit, 3 Upper & 3 Bottom Picture F...From $90.00Choose options
Wall Panels for Living Room, Flat Wall Molding KitFrom $246.00Choose options
Box Molding Kit, Shadow Box 2 Upper, 1 Center & 2 Bottom FramesFrom $188.40Choose options
Picture Frame Molding Set, Double Frame 1 to 4 PanelsFrom $83.76Choose options
Square Pre-Cut Flat Wall Molding Kit for Living AreasFrom $352.80Choose options
Peel and Stick Wall Molding Kit, 2 Upper & 2 Bottom FramesFrom $96.00Choose options
Quick Easy to Apply Peel and Stick Wall Molding, 3 Upper & 3 ...From $206.40Choose options
Vertical Wainscoting Wall Molding Kit, 3 Vertical FramesFrom $108.00Choose optionsProduct images and kit choices
These images come from the linked Trim Wall Haus product listings. They show the product style; the pictured configuration is not automatically the cut schedule on this page.
Instant Nested Frame Wall Trim Molding Package Kits, 3 Upper & 3 Bottom Nested Frames | Quick Easy Installation
Picture Frame Pre-Cut Flat Wall Molding Kit for Living Areas | Factory Primed & Paintable
Minimalist Flat Picture Frame Wall Molding Kit | Self-Adhesive Easy InstallationQuestions for this specific plan
How wide is the usable opening, rather than the outside frame?
The illustrated outer opening is 28.833 in / 732.367 mm wide after subtracting the two assumed 1.25-inch faces. A different profile changes this opening even when the outside frame dimensions stay the same.
How much trim does this 18 ft by 8 ft option use?
The listed schedule totals 112.833 linear ft / 34.392 m; the rounded 10% allowance is 125 linear ft / 38.1 m. Recalculate when changing count, profile, rail height or wall dimensions. This is a planning quantity, not a quoted kit configuration.
Where do I start marking the 6-division arrangement?
Use the finished left corner and floor as fixed datums. The first listed element begins 4 in / 101.6 mm from that corner. Mark each coordinate in the setting-out table directly rather than repeatedly stepping off rounded gaps.
Does ordering a linked kit guarantee these exact cuts?
No. The product photographs and links identify suitable looks. Confirm supplied sizes, frame count, profile width, material and installation method on the selected listing, then have a custom arrangement reviewed before ordering.
Continue with your wall measurements
Usable openings and trim-face coverage
| Calculated measurement | Result |
|---|---|
| Wall area above assumed baseboard | 135.75 sq ft |
| Estimated area covered by trim faces | 11.493 sq ft |
| Wall area outside trim faces | 124.257 sq ft |
| Trim-face share of wall above baseboard | 8.466% |
| Largest framed/grid rectangular opening | 28.833 in / 732.367 mm × 79 in / 2006.6 mm |
| Area of that rectangular opening | 15.818 sq ft |
| Artwork test with a 2-inch visual margin on all sides | 24.833 in / 630.767 mm × 75 in / 1905 mm |
Face coverage is the union of the drawn trim strips, excluding the existing 5.5-inch baseboard. Curved profiles use a centerline-length × face-width estimate. Wall area outside trim still includes areas behind reserved furniture; it is not a visible-paint estimate. The artwork test is a visual comparison, not a mounting clearance. For an arch, the rectangular opening is measured below the spring line.
Cut-stock fit with two assumed lengths
| Profile group | Assumed stock length | Stock pieces in this packing | Unallocated stock / limitation | Interpretation |
|---|---|---|---|---|
| Straight frame / board profile | 96 in / 2438.4 mm | 16 | 182 in / 4622.8 mm | Includes kerf and unusable remainder |
| Straight frame / board profile | 120 in / 3048 mm | 12 | 86 in / 2184.4 mm | Includes kerf and unusable remainder |
This is a first-fit decreasing packing example, not a claim of the minimum purchase quantity. Profile groups are packed separately; do not combine different actual products merely because they have the same nominal width. End trimming, damaged ends, join positions and fabrication details are not modeled. Stock lengths here are test inputs, not a statement of what the linked kits supply.
Compare ceiling heights on this wall width
Find the height closest to your measured ceiling. Each row recalculates the whole arrangement, including the example’s proportional rail/cap rule and Shaker row count. Open the matching height below the comparison for its complete drawing and cut schedule. Nested-frame outer clear dimensions and the largest uninterrupted inner opening describe different outlines.
| Ceiling | Bays/columns | Outer clear opening width | Outer clear opening height | Net listed trim | 10% allowance | Largest uninterrupted opening area | Trim-face share |
|---|---|---|---|---|---|---|---|
| 8 ft | 6 | 28.833 in / 732.367 mm | 79 in / 2006.6 mm | 112.833 linear ft / 34.392 m | 125 linear ft / 38.1 m | 15.818 sq ft | 8.466% |
| 8.5 ft | 6 | 28.833 in / 732.367 mm | 85 in / 2159 mm | 118.833 linear ft / 36.22 m | 131 linear ft / 39.929 m | 17.02 sq ft | 8.372% |
| 9 ft | 6 | 28.833 in / 732.367 mm | 91 in / 2311.4 mm | 124.833 linear ft / 38.049 m | 138 linear ft / 42.062 m | 18.221 sq ft | 8.288% |
| 9.5 ft | 6 | 28.833 in / 732.367 mm | 97 in / 2463.8 mm | 130.833 linear ft / 39.878 m | 144 linear ft / 43.891 m | 19.422 sq ft | 8.214% |
| 10 ft | 6 | 28.833 in / 732.367 mm | 103 in / 2616.2 mm | 136.833 linear ft / 41.707 m | 151 linear ft / 46.025 m | 20.624 sq ft | 8.147% |
| 10.5 ft | 6 | 28.833 in / 732.367 mm | 109 in / 2768.6 mm | 142.833 linear ft / 43.536 m | 158 linear ft / 48.158 m | 21.825 sq ft | 8.087% |
| 11 ft | 6 | 28.833 in / 732.367 mm | 115 in / 2921 mm | 148.833 linear ft / 45.364 m | 164 linear ft / 49.987 m | 23.027 sq ft | 8.033% |
8 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 81.5 in / 2070.1 mm | Outside long point; 45-degree miters |
Net listed trim: 112.833 linear ft / 34.392 m; rounded 10% allowance: 125 linear ft / 38.1 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
8.5 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 87.5 in / 2222.5 mm | Outside long point; 45-degree miters |
Net listed trim: 118.833 linear ft / 36.22 m; rounded 10% allowance: 131 linear ft / 39.929 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
9 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 93.5 in / 2374.9 mm | Outside long point; 45-degree miters |
Net listed trim: 124.833 linear ft / 38.049 m; rounded 10% allowance: 138 linear ft / 42.062 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
9.5 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 99.5 in / 2527.3 mm | Outside long point; 45-degree miters |
Net listed trim: 130.833 linear ft / 39.878 m; rounded 10% allowance: 144 linear ft / 43.891 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
10 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 105.5 in / 2679.7 mm | Outside long point; 45-degree miters |
Net listed trim: 136.833 linear ft / 41.707 m; rounded 10% allowance: 151 linear ft / 46.025 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
10.5 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 111.5 in / 2832.1 mm | Outside long point; 45-degree miters |
Net listed trim: 142.833 linear ft / 43.536 m; rounded 10% allowance: 158 linear ft / 48.158 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
11 ft ceiling: open the drawing and full cut schedule
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Tall horizontals | 12 | 31.333 in / 795.867 mm | Outside long point; 45-degree miters |
| Tall verticals | 12 | 117.5 in / 2984.5 mm | Outside long point; 45-degree miters |
Net listed trim: 148.833 linear ft / 45.364 m; rounded 10% allowance: 164 linear ft / 49.987 m. These cuts use the assumptions stated on this page. Confirm the actual profile, supplied lengths, joints and obstacles before ordering.
Related layouts and planning constraints
Popular pre-cut kits: Precut Bedroom Wall Trim Molding Kit · Shadow Box Ready to Assemble Wall Molding Package
Ready to transform your wall?
Pre-cut, factory primed kits. Free shipping. $20 off orders over $350 with code WALL20.
Calculate my wall Shop Picture Frame Molding Kits