Shaker Wall Panel Layout for a 19 ft Wall, 9.5 ft Ceiling
This 19 ft wall and 9.5 ft ceiling example compares complete Shaker wall panels arrangements, not only panel widths. Use the setting-out coordinates to mark the wall, then compare the material and clear-opening changes before selecting a kit.
How the width and openings were calculated
(228 − (7 + 1) × 3) ÷ 7 = 29.143 inches of clear opening. Dividing 228 by 7 without subtracting the boards would overstate each bay by 3.429 in / 87.086 mm.
Three-inch board faces, outer battens flush with the wall ends, 2.5-inch top and bottom rail faces, and a 5.5-inch existing baseboard. Rails and battens meet at square ends.
Compare complete alternatives for this wall
| Columns / bays | Clear opening width | Clear opening height | Listed pieces / runs | Net material | With 10% allowance | Difference |
|---|---|---|---|---|---|---|
| 6 | 34.5 in / 876.3 mm | 50.25 in / 1276.35 mm | 15 | 115.625 linear ft / 35.242 m | 128 linear ft / 39.014 m | 8.375 linear ft less trim |
| 7 | 29.143 in / 740.229 mm | 50.25 in / 1276.35 mm | 17 | 124 linear ft / 37.795 m | 137 linear ft / 41.758 m | Illustrated |
| 8 | 25.125 in / 638.175 mm | 50.25 in / 1276.35 mm | 19 | 132.375 linear ft / 40.348 m | 146 linear ft / 44.501 m | 8.375 linear ft more trim |
Across these options the net material ranges from 115.625 linear ft / 35.242 m to 132.375 linear ft / 40.348 m. Fewer divisions widen the openings; more divisions add vertical edges. Choose using furniture and artwork outlines rather than assuming the highest panel count is better. The cut schedule below belongs to the illustrated 7-division option.
Cut schedule and material allowance
| Component | Quantity | Length each / run | Measurement basis |
|---|---|---|---|
| Vertical battens | 8 | 103.5 in / 2628.9 mm | Square ends fitted between rails |
| Top or cap rail run | 1 | 228 in / 5791.2 mm | Total run; stock lengths and joins to confirm |
| Bottom rail run | 1 | 228 in / 5791.2 mm | Total run; stock lengths and joins to confirm |
| Intermediate infill rails | 7 | 29.143 in / 740.229 mm | Square ends between vertical battens |
The listed components total 124 linear ft / 37.795 m. A 10% cutting allowance, rounded up to a whole foot, gives 137 linear ft / 41.758 m. This includes only the listed components; baseboards, adhesive, paint and unlisted return pieces are separate. Continuous rails are total runs, not a promise of one supplied piece.
Setting-out positions from one fixed corner
Measure horizontally from the finished left corner and vertically up from the finished floor. The table uses outside frame edges or board edges, not the center of a pencil line. Mark positions directly from the origin so rounded gaps do not accumulate.
| Element | Left edge from corner | Right edge from corner | Top above floor | Bottom above floor |
|---|---|---|---|---|
| Batten 1 | 0 in / 0 mm | 3 in / 76.2 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 2 | 32.143 in / 816.429 mm | 35.143 in / 892.629 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 3 | 64.286 in / 1632.857 mm | 67.286 in / 1709.057 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 4 | 96.429 in / 2449.286 mm | 99.429 in / 2525.486 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 5 | 128.571 in / 3265.714 mm | 131.571 in / 3341.914 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 6 | 160.714 in / 4082.143 mm | 163.714 in / 4158.343 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 7 | 192.857 in / 4898.571 mm | 195.857 in / 4974.771 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
| Batten 8 | 225 in / 5715 mm | 228 in / 5791.2 mm | 111.5 in / 2832.1 mm | 8 in / 203.2 mm |
What changes when your measurement changes?
| Measured change | Clear width | Clear height | Recalculated net trim | Change from illustrated |
|---|---|---|---|---|
| Wall 227 in; same count | 29 in / 736.6 mm | 50.25 in / 1276.35 mm | 123.75 linear ft / 37.719 m | -0.25 linear ft |
| Wall 229 in; same count | 29.286 in / 743.857 mm | 50.25 in / 1276.35 mm | 124.25 linear ft / 37.871 m | 0.25 linear ft |
| Ceiling 120 in; same count | 29.143 in / 740.229 mm | 34.5 in / 876.3 mm | 145 linear ft / 44.196 m | 21 linear ft |
At a fixed count of 7, a one-inch wall-width error changes each frame or bay by 0.143 in / 3.629 mm. A different count, profile face or rail position requires a full recalculation. The taller-ceiling row follows this example’s proportional rail/cap rule; an existing fixed rail needs a separate calculation.
Three-inch boards compared with 75 mm boards
| Board face | Clear bay | Difference from 3-inch option |
|---|---|---|
| 3 in / 76.2 mm | 29.143 in / 740.229 mm | Illustrated |
| 2.953 in / 75 mm | 29.197 in / 741.6 mm | 0.054 in / 1.371 mm |
With 8 vertical boards, replacing 3-inch faces with 75 mm faces releases 0.378 in / 9.6 mm across the whole wall. Redistribute that width between the 7 clear bays instead of leaving it as an uneven end gap.
One, two or three rows behind a desk or sofa
| Rows | Clear opening height | Intermediate infill rails | Net material |
|---|---|---|---|
| 1 | 103.5 in / 2628.9 mm | 0 | 107 linear ft / 32.614 m |
| 2 | 50.25 in / 1276.35 mm | 7 | 124 linear ft / 37.795 m |
| 3 | 32.5 in / 825.5 mm | 14 | 141 linear ft / 42.977 m |
The illustrated opening ratio is 0.58 width to height. An opening close to 1 reads as near-square; this is a proportion comparison, not a required style rule. Draw the desk at both seated and standing heights before choosing which rail crosses behind it.
Product images and kit choices
These images come from the linked Trim Wall Haus product listings. They show the product style; the pictured configuration is not automatically the cut schedule on this page.
Shaker Wall Paneling Kit, 75 mm Boards | Pre-Cut MDF Easy Installation
Shaker MDF Paneling, Long-Lasting Pre-Cut for Easy Installation | Unprimed Wall Molding W:75mm x T:8mm
Shaker Square Grid Wall Paneling Kit | Pre-Cut MDF Decorative Wall PanelsQuestions for this specific plan
Can I use 75 mm boards on this 19 ft wall?
Yes, if the remaining kit details suit the plan. Recalculate the clear bay from 29.143 in / 740.229 mm to 29.197 in / 741.6 mm at the same 7-bay count. The supplied kit quantity still needs checking.
How much trim does this 19 ft by 9.5 ft option use?
The listed schedule totals 124 linear ft / 37.795 m; the rounded 10% allowance is 137 linear ft / 41.758 m. Recalculate when changing count, profile, rail height or wall dimensions. This is a planning quantity, not a quoted kit configuration.
Where do I start marking the 7-division arrangement?
Use the finished left corner and floor as fixed datums. The first listed element begins 0 in / 0 mm from that corner. Mark each coordinate in the setting-out table directly rather than repeatedly stepping off rounded gaps.
Does ordering a linked kit guarantee these exact cuts?
No. The product photographs and links identify suitable looks. Confirm supplied sizes, frame count, profile width, material and installation method on the selected listing, then have a custom arrangement reviewed before ordering.