Dining Room Picture Frame Molding Kits: Upper and Lower Frames

Dining room picture frame molding kits can divide a long wall above and below a rail. Match the upper composition to artwork and the lower composition to visible wall space around the dining furniture.

Worked example: 168 in / 4267.2 mm wall width, 108 in / 2743.2 mm ceiling. 8 frames; 110 linear ft / 33.528 m net listed trim.

Calculated planning drawing, not a customer-project photograph or a promise that a standard kit has these dimensions. Replace all assumed dimensions with your measured wall.

Decisions before choosing this layout

Specific decisions for Dining Room Picture Frame Molding Kits
Decision	What to compare	Measurement to record
Decision 1	Choose the rail position with the sideboard and chair backs in view.	Provide the artwork outside size, sideboard outline and the distance to each casing.
Decision 2	For an existing large artwork, draw its outside frame before choosing the panel divisions.	Mark the complete outside outline on the same measured elevation.
Decision 3	Let the nearest door casing set a clean end margin rather than leaving a narrow leftover panel.	Mark the complete outside outline on the same measured elevation.

Calculated design alternatives

Change one constraint and compare the complete plan
Option	Arrangement	Opening / width check	Height / radius check	Net trim	10% allowance
3 divisions	6 frames	45.5 in / 1155.7 mm smallest clear width	16.5 in / 419.1 mm smallest clear height	99.5 linear ft / 30.328 m	110 linear ft / 33.528 m
4 divisions	8 frames	32 in / 812.8 mm smallest clear width	16.5 in / 419.1 mm smallest clear height	110 linear ft / 33.528 m	122 linear ft / 37.186 m
5 divisions	10 frames	23.9 in / 607.06 mm smallest clear width	16.5 in / 419.1 mm smallest clear height	120.5 linear ft / 36.728 m	133 linear ft / 40.538 m

The 14 ft by 9 ft wall stays constant in this comparison. Each option has its own cut schedule; the schedule printed below belongs only to the illustrated option. Changing the reserved object width can affect side panels even when the wall size stays the same.

Cut schedule and material allowance

Components for the illustrated option
Component	Quantity	Length each / run	Measurement basis
Upper frame 1 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Upper frame 1 verticals	2	56 in / 1422.4 mm	Outside long point; 45-degree corners
Upper frame 2 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Upper frame 2 verticals	2	56 in / 1422.4 mm	Outside long point; 45-degree corners
Upper frame 3 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Upper frame 3 verticals	2	56 in / 1422.4 mm	Outside long point; 45-degree corners
Upper frame 4 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Upper frame 4 verticals	2	56 in / 1422.4 mm	Outside long point; 45-degree corners
Lower frame 1 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Lower frame 1 verticals	2	19 in / 482.6 mm	Outside long point; 45-degree corners
Lower frame 2 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Lower frame 2 verticals	2	19 in / 482.6 mm	Outside long point; 45-degree corners
Lower frame 3 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Lower frame 3 verticals	2	19 in / 482.6 mm	Outside long point; 45-degree corners
Lower frame 4 horizontals	2	34.5 in / 876.3 mm	Outside long point; 45-degree corners
Lower frame 4 verticals	2	19 in / 482.6 mm	Outside long point; 45-degree corners
Chair rail planning run	1	168 in / 4267.2 mm	Confirm joints and supplied lengths

The listed components total 110 linear ft / 33.528 m. A 10% cutting allowance, rounded up to a whole foot, gives 122 linear ft / 37.186 m. This includes only the listed components; baseboards, adhesive, paint and unlisted return pieces are separate. Continuous rails are total runs, not a promise of one supplied piece.

Set out the actual outlines

Element outside edges from the left corner and finished floor
Element	Left edge	Top above floor	Width	Height
Frame 1	6 in / 152.4 mm	100 in / 2540 mm	34.5 in / 876.3 mm	56 in / 1422.4 mm
Frame 2	46.5 in / 1181.1 mm	100 in / 2540 mm	34.5 in / 876.3 mm	56 in / 1422.4 mm
Frame 3	87 in / 2209.8 mm	100 in / 2540 mm	34.5 in / 876.3 mm	56 in / 1422.4 mm
Frame 4	127.5 in / 3238.5 mm	100 in / 2540 mm	34.5 in / 876.3 mm	56 in / 1422.4 mm
Frame 5	6 in / 152.4 mm	33 in / 838.2 mm	34.5 in / 876.3 mm	19 in / 482.6 mm
Frame 6	46.5 in / 1181.1 mm	33 in / 838.2 mm	34.5 in / 876.3 mm	19 in / 482.6 mm
Frame 7	87 in / 2209.8 mm	33 in / 838.2 mm	34.5 in / 876.3 mm	19 in / 482.6 mm
Frame 8	127.5 in / 3238.5 mm	33 in / 838.2 mm	34.5 in / 876.3 mm	19 in / 482.6 mm

Worked scenario: artwork and profile width

This 8 frames arrangement has 32 in / 812.8 mm smallest clear width and 16.5 in / 419.1 mm smallest clear height. Those clear openings subtract the assumed profile faces. Draw the outside artwork frame and any backplate within the opening, then compare another division count if the margins become narrow. Provide the artwork outside size, sideboard outline and the distance to each casing.

How much allowance changes the order quantity

Allowances for this exact component schedule
Planning allowance	Rounded total	Extra over net material
5%	116 linear ft / 35.357 m	6 linear ft / 1.829 m
10%	122 linear ft / 37.186 m	12 linear ft / 3.658 m
15%	127 linear ft / 38.71 m	17 linear ft / 5.182 m

These percentages compare planning quantities; they do not optimize cuts into stock lengths. More corners, short supplied lengths or difficult joins can change the allowance. Confirm the actual packing list before ordering.

Product images and kit choices

These images come from the linked Trim Wall Haus product listings. They show the product style; the pictured configuration is not automatically the cut schedule on this page.

Instant Nested Frame Wall Trim Molding Package Kits, 3 Upper & 3 Bottom Nested Frames | Quick Easy Installation — Image from the linked product listing. Compare its configuration with the drawing.

Picture Frame Pre-Cut Flat Wall Molding Kit for Living Areas | Factory Primed & Paintable — Image from the linked product listing. Compare its configuration with the drawing.

Minimalist Flat Picture Frame Wall Molding Kit | Self-Adhesive Easy Installation — Image from the linked product listing. Compare its configuration with the drawing.

Questions for this specific plan

How do I plan around an existing artwork?

Use the outside artwork frame, not the print size, and include any picture-light backplate. Compare that outline with the clear opening after subtracting the molding faces.

What measurements are assumed for this dining room picture frame molding kits example?

The wall is 168 in / 4267.2 mm wide and 108 in / 2743.2 mm high. The drawing and outline tables show the remaining assumptions. Provide the artwork outside size, sideboard outline and the distance to each casing.

How much trim is listed for the illustrated 14 ft wall?

The net listed schedule is 110 linear ft / 33.528 m; with a rounded 10% allowance it is 122 linear ft / 37.186 m. The alternatives above change the geometry and may change that total.

Will a product pictured below arrive in these exact dimensions?

Use the listing to check the supplied configuration, profile and installation method. The drawing is a design example; a changed wall, object outline or frame count requires confirmation of the actual kit parts.

Continue with your wall measurements

Plan my wall Compare matching kits Send a drawing for review

Usable openings and trim-face coverage

Additional measurements calculated from this exact drawing
Calculated measurement	Result
Wall area above assumed baseboard	119.583 sq ft
Estimated area covered by trim faces	12.569 sq ft
Wall area outside trim faces	107.014 sq ft
Trim-face share of wall above baseboard	10.511%
Largest framed/grid rectangular opening	32 in / 812.8 mm × 53.5 in / 1358.9 mm
Area of that rectangular opening	11.889 sq ft
Artwork test with a 2-inch visual margin on all sides	28 in / 711.2 mm × 49.5 in / 1257.3 mm

Face coverage is the union of the drawn trim strips, excluding the existing 5.5-inch baseboard. Curved profiles use a centerline-length × face-width estimate. Wall area outside trim still includes areas behind reserved furniture; it is not a visible-paint estimate. The artwork test is a visual comparison, not a mounting clearance. For an arch, the rectangular opening is measured below the spring line.

Cut-stock fit with two assumed lengths

Illustrative packing with a 1/8-inch gap between cuts; confirm actual supplied lengths
Profile group	Assumed stock length	Stock pieces in this packing	Unallocated stock / limitation	Interpretation
Straight frame / board profile	96 in / 2438.4 mm	13	96 in / 2438.4 mm	Includes kerf and unusable remainder
Straight frame / board profile	120 in / 3048 mm	11	168 in / 4267.2 mm	Includes kerf and unusable remainder
Chair rail	96 in / 2438.4 mm	Not a no-splice fit	1 listed pieces/runs exceed this length	Review joints or another supplied length
Chair rail	120 in / 3048 mm	Not a no-splice fit	1 listed pieces/runs exceed this length	Review joints or another supplied length

This is a first-fit decreasing packing example, not a claim of the minimum purchase quantity. Profile groups are packed separately; do not combine different actual products merely because they have the same nominal width. End trimming, damaged ends, join positions and fabrication details are not modeled. Stock lengths here are test inputs, not a statement of what the linked kits supply.