Board and Batten Layout Planner: Exact Batten Gaps for Any Wall

Free layout + quote: send your wall size and a photo and we plan the batten spacing around outlets and windows, then price the kit. Send your wall size

Enter your wall width, the batten width and how many battens you want. The calculator returns the exact clear gap between battens so the run stays even from corner to corner.

How to calculate board and batten spacing

The planner places a batten at each end of the wall and spaces the rest evenly. You choose how many battens you want and how wide they are; the gap follows from the wall width.

The formula

Gap = (wall width − battens × batten width) ÷ (battens − 1)

To start from a target gap instead: battens = (wall width + gap) ÷ (batten width + gap), then round to a whole number and recalculate the exact gap.

Worked example: a 10 ft wall

  • Wall: 120 in wide, battens 3 in wide, target gap about 16 in
  • Battens: (120 + 16) ÷ (3 + 16) = 7.2, so use 7 battens
  • Exact gap: (120 − 7 × 3) ÷ 6 = 16.5 in

Batten gaps for common walls (3 in battens)

Wall width Battens Batten width Gap
8 ft (96 in) 6 3 in 15.60 in
10 ft (120 in) 7 3 in 16.50 in
12 ft (144 in) 9 3 in 14.62 in
14 ft (168 in) 10 3 in 15.33 in
16 ft (192 in) 12 3 in 14.18 in

Board and batten height calculator

Classic board and batten stops at about five eighths of the wall: 60 in on an 8 ft ceiling, 67.5 in on 9 ft, 75 in on 10 ft. Half-wall versions stop at 36 to 42 in. Batten length = ledge height − baseboard − rail width.

Board and batten accent wall calculator

For a grid accent wall, size the squares first. Columns = round((wall width − board) ÷ (target square + board)), rows = round((wall height − baseboard − board) ÷ (target square + board)). With 3 in boards and 24 in squares, a 10 ft by 8 ft wall becomes a 4 by 3 grid of 26 in panels. See 10 ft grid layout and 12 ft grid layout.

Board and batten siding vs interior walls

Exterior siding uses wider boards and gaps set by the siding product. For interior accent walls the 12 to 18 in gap range above applies; these numbers are for interior MDF battens.

Rules of thumb

  • Gaps of 12 to 18 in suit most rooms; tighter gaps read more traditional, wider gaps more modern.
  • A board and batten wainscot usually stops at one third of the wall height; a top rail of 1 to 1.5 in finishes the edge.
  • Measure at the floor and at the ceiling line: older walls are rarely square, so use the shorter width.

Full layouts by wall size: 10 ft · 12 ft · 12 ft with 9 ft ceiling · Batten trim guide · Picture frame and wainscoting calculator

Get a free layout and quote

Send your wall width, height and outlet positions. We return a batten layout and a price for battens cut to your wall. Send your wall size →

Board and batten spacing calculator

Enter the usable width of one wall. This calculates the clear space between evenly spaced vertical battens.

Clear gap between battens19.2 inCheck actual material dimensions before ordering.

How to calculate board and batten spacing

This free board and batten calculator removes both side margins and the total width of every batten from the usable wall width. It divides the remaining space into equal clear gaps so the vertical battens finish evenly from one side of the wall to the other.

  1. Measure the usable wall width and subtract areas blocked by doors or built-in furniture.
  2. Enter the actual batten width, not the nominal lumber size.
  3. Adjust the batten count until the clear gap suits the room scale and wall height.

For a complete layout, use our picture frame molding calculator, request a free architectural drawing, or compare pre-cut board and batten wall kits.

Board and batten calculator questions

How far apart should board and batten strips be?

The right gap depends on wall width, batten width and the number of vertical battens. Equal clear gaps usually create the cleanest result; use the calculator to test several counts.

Should I include the corner battens?

Enter the total number of vertical battens used across the measured run. Keep the side margin fields for any clear space you want to leave at both wall edges.

Can Trim Wall Haus prepare a custom layout?

Yes. Send a photo and measurements to info@trimwallhaus.com for complimentary architectural drawing support before ordering your kit.